Starter interrupt devices are a common annoyance for many car owners. They’re small, unobtrusive devices that sit between the battery and the engine. If you ever have to jump your car, for example, the starter interrupt device will prevent the engine from turning over until you remove it. If you ever have to disable a starter interrupt device, there are a few things you need to know how to disable starter interrupt device.
Here are 8 tips on how to disable a starter interrupt device:
(1) Find the fuse that controls the starter interrupt device. It will likely be near the battery.
(2) Remove the fuse, and replace it with a 10 amp fuse.
(3) Reconnect the battery cables.
(4) Turn on the car, and wait until it stalls (the engine should not start).
(5) Disconnect the battery cables again.
(6) Repeat steps 2-5 until the car will not start with either battery cable disconnected.
(7) Reconnect one of the battery cables, and turn on the car. The engine should still stall.
(8) Remove the other battery cable, and turn off the car. The engine should now start.
What is a Starter Interrupt Device?
A starter interrupt device (SID) is a safety mechanism that prevents the engine from starting if the car’s power steering or suspension are not operational. To disable a SID, you must first identify which vehicle you’re working on and then access the factory service manual. There, you’ll find diagrams of the SID circuitry and instructions on how to disable it.
How to Disable a Starter Interrupt Device
When you buy a new car, there may be a starter interrupt device (SID) already installed. This is a small electronic device that can disable the engine if it detects an unauthorized start.
To disable the SID:
1. Park the car in your garage or driveway so that you have full control over the vehicle.
2. Remove the battery cable. You can do this by undoing the two screws that hold on the battery tray, or by pulling up on one end of the cable and pulling outwards.
3. Disconnect all cables connected to the SID, including power, ground, and emissions sensors.
4. Reconnect all cables to the SID in reverse order (power, then ground, then emissions). Make sure that each wire is securely attached to its corresponding connector.
5. Reinstall battery tray screws and cable ties or replace battery if removed in step 2.
Disabling the Starter Interrupt Device in Windows 10
Windows 10 provides a way to disable the starter interrupt device. To do this, open the Start menu and type “powercfg -h .” In the resulting window, under “Hardware profile,” select “System Configuration.” In the “System Policies” section, double-click on “Startup/Shutdown.” On the right side of the window, under “Starter Interrupts,” click on the drop-down box next to “Enabled.” Click on the check box next to “Disabled.” Click on OK.
This will disable the startup process for your computer. You will still be able to start your computer by pressing down on the power button, but you will not be able to use the Windows 10 startup process.
Disabling the Starter Interrupt Device in Windows 8
Windows 8 includes a new startup process that allows for easier troubleshooting. One downside is that this new process can disable devices that are needed to boot the computer, including the starter interrupt device.
To disable the starter interrupt device in Windows 8:
1.Click on the Start button and then click on the Control Panel menu.
2.Click on System and Security.
3.Click on Startup and Recovery.
4.Click on Change how Windows starts up.
5.Under “Booting options,” uncheck “Use automatic starting of services and applications.”
6.Disable the “Starter Interrupt Device” by checking the box next to it and clicking on OK.
Disabling the Starter Interrupt Device in Windows 7
In Windows 7, the starter interrupt device (SID) is used to disable certain startup procedures. Disabling the SID can help improve system performance and stability. To disable the SID, follow these steps:
1. Open the Windows Configuration Manager tool by clicking Start, typing “configuration”, and pressing Enter.
2. In the console tree, navigate to System devices > Device Manager.
3. Right-click the Unknown device and select Properties.
4. On the General tab, click Device Interrupt Level setting and change it to Level 3 (Halt).
5. Click OK to close the Properties window, and close Device Manager.
Conclusion
If your car has a starter interrupt device, you may find that it is preventing you from starting your car. This article will show you how to disable the starter interrupt device on most cars.
